Power and distribution transformers represent the single most expensive capital asset in any high-voltage electrical substation. When a transformer fails in an industrial zone like Faisalabad’s M-3 Industrial City or Karachi’s SITE area, the financial damage extends far beyond the cost of rewinding or replacement. Plant downtime, lost production batches, and emergency grid penalties from DISCOs (such as FESCO, LESCO, or K-Electric) can cost tens of millions of PKR within days.
Monitoring the dielectric fluid within these units provides an accurate assessment of internal mechanical and thermal health. Mineral insulating oil serves two essential functions: it acts as a high-dielectric-strength insulator and circulates as a heat transfer medium. When electrical or thermal stresses occur within the tank, the chemical bonds of the hydrocarbon oil and cellulose paper insulation break down, generating specific byproduct gases. Dissolved Gas Analysis (DGA) is the industry standard diagnostic technique used to detect, identify, and quantify these gases before catastrophic failure occurs.
The Core Chemistry of Dissolved Gas Analysis (DGA)
Under normal operating conditions, a well-maintained transformer generates minute amounts of atmospheric gases through routine thermal cycling. However, when abnormal electrical or thermal stresses develop, the hydrocarbon molecules ($C_n H_{2n+2}$) of the mineral oil crack into lighter reactive radicals, which rapidly recombine into specific combustible and non-combustible gases.
Seven primary fault gases are tracked during routine DGA laboratory testing:
* Hydrogen ($H_2$): Primarily produced by low-energy partial discharge (corona) phenomena and stray gassing at moderate temperatures. It is generated whenever free electrons collide with hydrocarbon molecules. * Methane ($CH_4$) and Ethane ($C_2H_6$): Low-to-medium thermal fault indicators. Methane typically appears when oil undergoes thermal breakdown between 150°C and 300°C, while ethane generation accelerates between 300°C and 500°C. * Ethylene ($C_2H_4$): High-temperature thermal fault marker. Ethylene requires significant energy to form, typically pointing to localized hotspot temperatures in the oil or metallic parts exceeding 500°C to 700°C (such as loose busbar connections or core-lamination shorts). * Acetylene ($C_2H_2$): The most critical gas. Acetylene forms almost exclusively under extreme energy conditions exceeding 800°C to 1000°C, characteristic of electrical arcing, continuous sparking, or tap-changer flashovers. The presence of even 2 to 3 parts per million (ppm) of acetylene demands immediate attention. * Carbon Monoxide ($CO$) and Carbon Dioxide ($CO_2$): Primary indicators of solid cellulose insulation (Kraft paper and pressboard) thermal degradation, rather than oil breakdown alone.
Diagnostic Standards and Ratio Methods: IEC 60599 and IEEE C57.104
Detecting individual gas levels in parts per million provides an initial alert, but raw numbers alone do not pinpoint the root cause. International diagnostic bodies rely on standardized ratio calculations and graphical coordinate systems to correlate gas generation rates with specific physical fault mechanisms.
The IEC 60599 standard utilizes gas ratios to classify faults into distinct operational categories. By calculating three key ratios—$C_2H_2 / C_2H_4$, $CH_4 / H_2$, and $C_2H_4 / C_2H_6$—engineers can differentiate between partial discharge of low energy density, partial discharge of high energy density, thermal faults below 300°C, thermal faults up to 700°C, and thermal faults exceeding 700°C.
Complementing ratio methods, the Duval Triangle (primarily Triangle 1) has become the global benchmark for visual confirmation. Developed by Michel Duval, this system plots the relative percentages of three critical gases against a triangular coordinate grid:
$$\% CH_4 = \frac{CH_4}{CH_4 + C_2H_4 + C_2H_2} \times 100$$ $$\% C_2H_4 = \frac{C_2H_4}{CH_4 + C_2H_4 + C_2H_2} \times 100$$ $$\% C_2H_2 = \frac{C_2H_2}{CH_4 + C_2H_4 + C_2H_2} \times 100$$
The resulting coordinates fall into specific fault zones: PD (Partial Discharge), T1 (Thermal Fault $< 300^\circ\text{C}$), T2 (Thermal Fault between $300^\circ\text{C}$ and $700^\circ\text{C}$), T3 (Thermal Fault $> 700^\circ\text{C}$), D1 (Discharge of Low Energy/Sparking), D2 (Discharge of High Energy/Arcing), or DT (Mixed Electrical and Thermal Fault). This method eliminates the "indeterminate" results occasionally yielded by standard mathematical ratios.
Interpreting Solid Insulation Degradation: The CO/CO2 Ratio
While oil can be degassed, filtered, or entirely replaced on-site, the degradation of Kraft paper insulation wrapping the copper windings is irreversible. Once paper insulation loses its mechanical tensile strength, the transformer reaches the end of its physical life, as short-circuit forces will shatter the brittle cellulose and cause phase-to-phase faults.
DGA monitors paper health through the ratio of carbon dioxide to carbon monoxide ($CO_2 / CO$). In a healthy, modern conservator-type transformer, the normal $CO_2 / CO$ ratio typically ranges between 6 and 10.
A declining ratio signals accelerated degradation: * $CO_2 / CO < 3$: Strong indication of rapid cellulose breakdown caused by localized high-temperature hotspots in the paper, even if overall oil temperatures appear moderate. * $CO_2 / CO > 20$: Can indicate low-temperature oxidation of paper insulation in the presence of excessive atmospheric moisture and oxygen ingress.
When carbon oxide ratios indicate severe paper aging, DGA should be supplemented with high-performance liquid chromatography (HPLC) to test for 2-Furfuraldehyde (2-FAL). Furan concentrations directly correlate to the Degree of Polymerization (DP) of the paper. New transformer paper features a DP value between 1,000 and 1,200. A drop below 200 to 250 DP indicates that the paper has reached its mechanical end-of-life, warning the maintenance team that the transformer cannot safely withstand through-fault stresses from downstream short circuits.
Operational Realities in Pakistan: Thermal Stress and Environmental Challenges
Interpreting DGA data in Pakistan requires adjusting baseline assumptions to account for local operational parameters. Transformers deployed across industrial facilities in Punjab and Sindh operate under harsher environmental conditions than units tested under temperate European or North American field baselines.
First, ambient temperatures in industrial hubs like Faisalabad, Multan, and Sukkur routinely exceed 45°C during summer months. Because transformer cooling (whether ONAN or ONAF) relies directly on the differential between ambient air and radiator surfaces, top-oil temperatures frequently approach design limits (65°C rise over ambient). These elevated base operating temperatures accelerate stray gassing—generating baseline methane and hydrogen without an actual active electrical fault present.
Second, cyclic load shedding and severe grid voltage fluctuations impose significant thermal and dielectric shock on industrial units. Repeated energization surges combined with shifting loads (from full plant operation to captive diesel/gas generation switchovers) generate localized dielectric stresses in winding bushings and off-circuit tap changers (OCTC).
Third, inadequate maintenance of silica gel breathers allows humid, monsoonal air to enter conservator tanks. Water content in mineral oil should ideally remain below 15 to 20 ppm. When moisture climbs past 35 ppm, it acts as a catalyst, cutting paper life in half for every 1% increase in moisture content and accelerating gas evolution rates. Abdullah International routinely evaluates these ambient factors during substation audits across Pakistani textile, chemical, and manufacturing facilities.
Testing Protocols, Lab Selection, and PKR Cost Benchmarks
Obtaining accurate DGA results depends directly on proper sampling procedure. Taking an oil sample from a transformer drain valve without correct flushing or using an unsealed plastic bottle invalidates the test; dissolved gases, particularly volatile hydrogen and methane, will rapidly escape into the atmosphere.
Samples must be drawn using gas-tight, ground-glass syringes (50 ml or 100 ml capacity) equipped with three-way stopcocks, or certified stainless steel sampling cylinders, adhering strictly to ASTM D923 and IEC 60475 guidelines. The drain valve must be thoroughly flushed to clear settled sediment and stagnant oil from the pipe stub before filling the syringe without introducing ambient air bubbles.
In Pakistan, industrial facilities rely on accredited laboratories for gas chromatography testing, including the High Voltage & Short Circuit Laboratory (HV&SC) in Rawat, PCSIR facilities, or accredited third-party electrical service laboratories.
Typical testing costs in Pakistan (exclusive of sales taxes) are:
* Standard DGA (7 key gases via gas chromatography): PKR 18,000 to PKR 30,000 per sample. * Comprehensive Screen (DGA + Dielectric Breakdown Voltage + Moisture Content + Acidity/Interfacial Tension): PKR 38,000 to PKR 65,000 per unit. * Furan Analysis (HPLC testing for DP estimation): PKR 25,000 to PKR 40,000 per sample.
For industrial transformers rated above 2.5 MVA, routine testing should occur every 6 to 12 months. For smaller 11kV distribution units (such as 630 kVA or 1,000 kVA step-down units), an annual or bi-annual screen is acceptable, provided the unit has not tripped on Buchholz or differential protection.
Remediation Strategies: From Oil Conditioning to Internal Inspection
A critical DGA report does not automatically mean a transformer must be decommissioned. Actionable intervention depends on the specific fault zone identified:
``
[DGA Lab Report Received]
│
├─► Acetylene (C2H2) > 2 ppm or Duval Zone D1/D2
│ │
│ └─► High-energy fault: Perform winding resistance,
│ turns ratio (TTR), & SFRA before re-energizing.
│
├─► Ethylene (C2H4) High or Duval Zone T2/T3
│ │
│ └─► Hotspot: Thermographic inspection of bushings,
│ core grounding, and tap-changer contacts.
│
└─► Elevated H2 / CH4 / Moisture, but Normal C2H2
│
└─► On-site high-vacuum oil dehydration & degassing
(Target: < 10 ppm moisture, > 60 kV BDV).
``
When DGA indicates elevated low-to-medium thermal gases along with high moisture levels, on-site oil processing is the correct engineering remedy. Mobile high-vacuum oil filtration units can process transformer oil under vacuum heating (typically 60°C to 65°C at pressures below 1 mbar). This process extracts dissolved combustible gases, removes free and dissolved water, and filters particulate carbon down to sub-micron levels.
Contracting an on-site mobile vacuum filtration plant in Pakistan typically costs between PKR 90,000 and PKR 280,000, depending on oil volume (ranging from 1,500 liters for a distribution unit to 10,000+ liters for a power transformer) and site logistics. Abdullah International provides structured maintenance workflows to verify that post-treatment dielectric breakdown voltage (BDV) exceeds 60 kV and moisture is driven down to acceptable limits before system re-energization.
If DGA reveals significant acetylene ($C_2H_2$) generation or Duval Zone D2 arcing, filtration alone is unacceptable. Degassing an arcing unit merely removes the symptoms while the active electrical tracking continues to burn paper and carbonize copper. Such units must be de-energized immediately for diagnostic electrical testing, including transformer turns ratio (TTR), winding resistance, insulation resistance (Megger), and sweep frequency response analysis (SFRA) to locate internal winding displacement or core-ground faults.
Conclusion
Dissolved Gas Analysis transforms transformer oil from a simple insulating liquid into an information-rich predictive diagnostic tool. By identifying specific fault gases, applying the Duval Triangle, and monitoring the $CO_2 / CO$ ratio, engineering teams can detect thermal hotspots, arcing, and paper degradation months before an unscheduled breakdown halts plant production. Establish an annual DGA baseline schedule for all substation transformers rated 1,000 kVA and above, and mandate certified gas-tight glass syringe sampling to ensure reliable laboratory data that protects your high-voltage capital investments.

